VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit carton specs template guide
starter vape kits · wholesale buyers

Starter Vape Kit carton specs template guide

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for wholesale buyers.

Published 01 May 2026  ·  VapeWholesaleHub  ·  Reading time 7 min

Packaging proof for the export market, approved before the run.
Packaging proof for the export market, approved before the run.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.

What we test before a carton is sealed

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

What happens when something goes wrong

Technical questions usually arrive at the worst possible moment, which is why we answer them on WhatsApp as well as email. A photo and a two line message resolves most issues faster than a ticket.

Reorders are the real test of a supplier. If the second shipment does not match the first, the relationship is over regardless of price, so we treat the reorder as the actual deliverable.

For wholesale buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

How the price is actually built

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

We publish a realistic band of 2.98 to 8.19 per unit for standard configurations at 240 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

  • Mixed SKU cartons to spread first-order risk
  • Document pack prepared per destination market
  • Seven-day defect reporting with replace-or-credit
  • Reference sample retained from every batch
  • Consolidated or split shipping, quoted both ways
  • Artwork proof plus physical dummy for custom packaging

Shipping without surprises

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

Documentation travels with the goods: commercial invoice, packing list, and the certificate set for your market. We send a scanned copy before dispatch so your broker can clear the file in advance.

Specification summary

Typical specification for this category
Battery350 mAh
Pod capacity2.0 ml
Coil resistance0.8 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order50 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

What is the minimum order for starter vape kit?

Standard configurations start at 240 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 600 units because of setup time on the line.

How long does production take?

Around 15 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us