VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit small batch: entry level
starter vape kits · wholesale buyers

Starter Vape Kit small batch: entry level

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for wholesale buyers.

Published 21 July 2026  ·  VapeWholesaleHub  ·  Reading time 8 min

Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.

Assortment planning without the guesswork

We work with wholesale buyers who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

When you compare suppliers for starter vape kit, ask for the last three production dates on the same SKU. If the answers are vague, the specification is not being held and the next batch will not match the sample you approved.

A practical starting order for wholesale buyers is 300 units across two or three SKUs, not 300 units of one. That spreads the risk, gives your staff something to compare, and still hits the first price break.

Paperwork, labelling and market rules

Regulation for starter vape kits differs by country and sometimes by state. We do not pretend to be your lawyer, but we do keep the document pack current and we will tell you when a configuration cannot legally enter a market you have named.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

For wholesale buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

What we test before a carton is sealed

Flavour drift between batches is the quiet killer of repeat orders. We retain a sealed reference sample from every run so a complaint six weeks later can be compared against what actually left the building.

We photograph the packing station during production for volume orders. It is a small thing, but it settles most arguments about what was actually in the carton before it was sealed.

  • Cartons drop-tested and pallet-counted for clean freight
  • Private label files archived for future rebrands
  • Specification locked in writing before production starts
  • Document pack prepared per destination market
  • Seven-day defect reporting with replace-or-credit
  • Named account contact who has handled the product

After-sales, replacements and reorders

Technical questions usually arrive at the worst possible moment, which is why we answer them on WhatsApp as well as email. A photo and a two line message resolves most issues faster than a ticket.

Every account gets a named contact who has actually seen the product. Being passed between three people to answer one question about a coil resistance is the fastest way to lose a buyer, so we do not organise support that way.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity2.0 ml
Coil resistance1.0 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order50 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

We would rather lose an order at quotation stage than explain a mismatch after delivery, which is why the specification conversation comes before the price conversation.

Frequently asked

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

How long does production take?

Around 28 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us